Hi Alexei,
I captured the LOG_LEVEL=50 log (attached putty-ser0.log https://www.dropbox.com/s/bi3hngmljksxl3a/putty-ser0.log?dl=0) from TF-A bl31.bin. I see bl31 boots normally but never hands off to the BL33 normal world image (App.bin)
The flash.bin image I am running is constructed using imx-mkimage https://source.codeaurora.org/external/imx/imx-mkimage/tree/README?h=imx_4.14.98_2.0.0_ga tool with the following target:
flash_test_7: $(MKIMG) mx8qm-ahab-container.img scfw_tcm.bin bl31.bin App.bin imx8qm-mek-ca53.dtb
./$(MKIMG) -soc QM -rev B0 -append mx8qm-ahab-container.img -c -flags 0x00200000 -scfw scfw_tcm.bin -ap bl31.bin a53 0x80000000 -p3 -ap App.bin a53 0x80020000 -data imx8qm-mek-ca53.dtb 0x83000000 -out flash.bin
I used UUU tool to flash eMMC with flash.bin on the imx8QM MEK board.
I inspected RAM using a trace32 debugger SW after using a while (1) to halt the execution at the end of bl31.bin main function (bl31_main()).
diff --git a/bl31/bl31_main.c b/bl31/bl31_main.c
index 92a2027dd..51afb13ea 100644
--- a/bl31/bl31_main.c
+++ b/bl31/bl31_main.c
@@ -147,6 +147,11 @@ void bl31_main(void)
* from BL31
*/
bl31_plat_runtime_setup();
- INFO("BL31: leaving bl31_main\n");
- INFO("entering while(1)\n");
- while (1) {};
}
It appears that there's no data or image at 0x80020000 just before exiting bl31_main(). See the debugger RAM dump at address 0x80000000 (bl31.bin entry point) and 0x80020000 (BL33 or App.bin normal world app entry point). See the debugger output https://www.dropbox.com/s/revv4qev2ky5djj/ksnip_20201022-153339.png?dl=0.
When should the flash image provided in flash.bin get copied to the RAM entry point 0x80020000 ? Should bl31.bin copy the image from flash to RAM ?
Can you suggest what could be going on ?
Regards Ravi
On Oct 22, 2020, at 6:15 AM, Alexei Fedorov <Alexei.Fedorov@arm.com mailto:Alexei.Fedorov@arm.com> wrote:
Hi Ravi,
TFTF image can be built from https://git.trustedfirmware.org/TF-A/tf-a-tests.git https://git.trustedfirmware.org/TF-A/tf-a-tests.git
You can also try to increase TF-A log level by setting LOG_LEVEL=50 and check if BL33 memory region is mapped correctly. Before passing control to BL33 and could add code to dump initial memory at BL33 start address to see if the image was loaded with no issues.
Regards. Alexei
From: rkohli2000 gmail <rkohli2000@gmail.com mailto:rkohli2000@gmail.com> Sent: 21 October 2020 19:59 To: Alexei Fedorov <Alexei.Fedorov@arm.com mailto:Alexei.Fedorov@arm.com> Cc: Manish Pandey2 <Manish.Pandey2@arm.com mailto:Manish.Pandey2@arm.com>; tf-a@lists.trustedfirmware.org mailto:tf-a@lists.trustedfirmware.org <tf-a@lists.trustedfirmware.org mailto:tf-a@lists.trustedfirmware.org> Subject: Re: [TF-A] BL31 as bootloader Alexei,
I don't have a DS-5 debugger setup/licensed. I am hoping on getting something shortly.
Can you point me to the TFTF image that I can use to test the BL33 handoff ?
Sorry, I'm not familiar at this time.
Regards Ravi
On Oct 21, 2020, at 12:35 PM, Alexei Fedorov <Alexei.Fedorov@arm.com mailto:Alexei.Fedorov@arm.com> wrote:
You can also use TFTF image as BL33.
Alexei
From: Manish Pandey2 <Manish.Pandey2@arm.com mailto:Manish.Pandey2@arm.com> Sent: 21 October 2020 15:26 To: rkohli2000 gmail <rkohli2000@gmail.com mailto:rkohli2000@gmail.com>; Alexei Fedorov <Alexei.Fedorov@arm.com mailto:Alexei.Fedorov@arm.com> Cc: tf-a@lists.trustedfirmware.org mailto:tf-a@lists.trustedfirmware.org <tf-a@lists.trustedfirmware.org mailto:tf-a@lists.trustedfirmware.org> Subject: Re: [TF-A] BL31 as bootloader The best way to figure out whether handing off to BL33 happened or not is by attaching a debugger(DS-5).
is there any other A53 (or A72) test image (hello world like) I can validate with to further debug ?
- You can use a linux image and device tree to test it
Refer to plat/brcm/common/brcm_bl31_setup.c -> "brcm_bl31_early_platform_setup()" function For linux as BL33 payload please use coder under "ARM_LINUX_KERNEL_AS_BL33"
From: rkohli2000 gmail <rkohli2000@gmail.com mailto:rkohli2000@gmail.com> Sent: 21 October 2020 12:12 To: Alexei Fedorov <Alexei.Fedorov@arm.com mailto:Alexei.Fedorov@arm.com> Cc: Manish Pandey2 <Manish.Pandey2@arm.com mailto:Manish.Pandey2@arm.com>; tf-a@lists.trustedfirmware.org mailto:tf-a@lists.trustedfirmware.org <tf-a@lists.trustedfirmware.org mailto:tf-a@lists.trustedfirmware.org> Subject: Re: [TF-A] BL31 as bootloader Hi Alexei, Manish,
I tried the following patch to plat/imx/imx8qm/imx8qm_bl31_setup.c:
@@ -483,11 +486,15 @@ void bl31_early_platform_setup2(u_register_t arg0, u_register_t arg1, bl32_image_ep_info.args.arg3 = BL32_FDT_OVERLAY_ADDR; #endif #endif
- // DEBUG ONLY - FIXME
- SET_PARAM_HEAD(&bl33_image_ep_info, PARAM_EP, VERSION_1, 0);
SET_SECURITY_STATE(bl33_image_ep_info.h.attr, NON_SECURE);/* init the first cluster's cci slave interface */ cci_init(PLAT_CCI_BASE, imx8qm_cci_map, PLATFORM_CLUSTER_COUNT); cci_enable_snoop_dvm_reqs(MPIDR_AFFLVL1_VAL(read_mpidr_el1()));
}
But no luck.
Is there some way to confirm my bl31.bin is handing off to any BL33 (normal world) test image ? In other words, is there any other A53 (or A72) test image (hello world like) I can validate with to further debug ?
Thanks.
On Oct 21, 2020, at 6:10 AM, Alexei Fedorov <Alexei.Fedorov@arm.com mailto:Alexei.Fedorov@arm.com> wrote:
Hi Ravi,
You can take a look at arm_bl31_early_platform_setup() in plat\arm\common\arm_bl31_setup.c:
/* Populate entry point information for BL33 */ SET_PARAM_HEAD(&bl33_image_ep_info, PARAM_EP, VERSION_1, 0); /*
- Tell BL31 where the non-trusted software image
- is located and the entry state information
*/ bl33_image_ep_info.pc = plat_get_ns_image_entrypoint();
bl33_image_ep_info.spsr = arm_get_spsr_for_bl33_entry(); SET_SECURITY_STATE(bl33_image_ep_info.h.attr, NON_SECURE);
Regards. Alexei
From: TF-A <tf-a-bounces@lists.trustedfirmware.org mailto:tf-a-bounces@lists.trustedfirmware.org> on behalf of rkohli2000 gmail via TF-A <tf-a@lists.trustedfirmware.org mailto:tf-a@lists.trustedfirmware.org> Sent: 21 October 2020 10:57 To: Manish Pandey2 <Manish.Pandey2@arm.com mailto:Manish.Pandey2@arm.com> Cc: tf-a@lists.trustedfirmware.org mailto:tf-a@lists.trustedfirmware.org <tf-a@lists.trustedfirmware.org mailto:tf-a@lists.trustedfirmware.org> Subject: Re: [TF-A] BL31 as bootloader Hi Manish,
The test image should not have any dependency on device tree (dtb?) for console init. I used the NXP provided imx8qm-mek-ca53.dtb file which should match the MEK board. I have tested removing "--data imx8qm-mek-ca53.dtb 0x83000000" (below) as well but no luck. I don't believe PC is getting set to the 0x80020000 entry point.
The test image has validated with u-boot using these tftpboot settings: setenv ipaddr x.x.x.x setenv serverip x.x.x.x tftpboot 0xf0000000 App.bin bootm 0xf0000000
I don't see any console output on the screen running it with bl31.bin as below. Is there any debug I can add somewhere to help troubleshoot?
Can you please provide me instructions on where to patch this missing code : "SET_PARAM_HEAD(&bl33_image_ep_info, PARAM_EP, VERSION_1, 0);" I can try it to see if any change in behavior.
Thanks in advance. Regards Ravi
On Wed, Oct 21, 2020 at 5:15 AM Manish Pandey2 <Manish.Pandey2@arm.com mailto:Manish.Pandey2@arm.com> wrote:
Hi Ravi,
Can you please confirm if control reached "test image" ? I guess, yes, as PC has right value. Also, does your "test image" depends on device tree for console initialization?
One thing i see missing in "plat/imx/imx8qm/imx8qm_bl31_setup.c +352" is bl33 header initialization SET_PARAM_HEAD(&bl33_image_ep_info, PARAM_EP, VERSION_1, 0);
thanks Manish
From: TF-A <tf-a-bounces@lists.trustedfirmware.org mailto:tf-a-bounces@lists.trustedfirmware.org> on behalf of rkohli2000 gmail via TF-A <tf-a@lists.trustedfirmware.org mailto:tf-a@lists.trustedfirmware.org> Sent: 21 October 2020 00:10 To: Ravi Kohli <rkohli2000@gmail.com mailto:rkohli2000@gmail.com> Cc: tf-a@lists.trustedfirmware.org mailto:tf-a@lists.trustedfirmware.org <tf-a@lists.trustedfirmware.org mailto:tf-a@lists.trustedfirmware.org> Subject: Re: [TF-A] BL31 as bootloader
Hi Alexei,
I built my TF-A (imx-atf) b31.bin image using the RESET_TO_BL31 build option for the i.MX8QM MEK dev kit.
make DEBUG=1 RESET_TO_BL31=1 PLAT=imx8qm bl31
I used the imx-mkimage tool to generate a flash.bin (flash bootable image) with the following target to run on the MEK:
flash_cortex_a53: $(MKIMG) mx8qm-ahab-container.img scfw_tcm.bin bl31.bin MyA53Serial.bin imx8qm-mek-ca53.dtb ./$(MKIMG) -soc QM -rev B0 -append mx8qm-ahab-container.img -c flags 0x00200000 -scfw scfw_tcm.bin -ap bl31.bin a53 0x80000000 -c -p3 -ap MyA53Serial.bin a53 0x80020000 -p4 --data imx8qm-mek-ca53.dtb 0x83000000 -out flash.bin
Here, I allocated bl31.bin to boot from 0x80000000 and a test image at BL33 (normal world) entry point 0x80020000 (both for Cortex-A53). I can see DEBUG console output from the bl31.bin image but no serial output from my test image I am trying to boot from 0x80020000.
NOTICE: Memreg 3 0x38000000 -- 0x3bffffff NOTICE: Memreg 4 0x60000000 -- 0x6fffffff NOTICE: Memreg 5 0x70000000 -- 0x7fffffff NOTICE: Memreg 6 0x80000000 -- 0xffffffff NOTICE: Memreg 7 0x400000000 -- 0x43fffffff NOTICE: Memreg 8 0x880000000 -- 0x97fffffff NOTICE: Non-secure Partitioning Succeeded NOTICE: BL31: v2.2(debug):imx_5.4.24_er3-1-g06450210f-dirty NOTICE: BL31: Built : 17:33:32, Oct 20 2020 INFO: bl31_platform_setup is called INFO: GICv3 with legacy support detected. ARM GICv3 driver initialized in EL3 INFO: BL31: Initializing runtime services INFO: BL31: cortex_a53: CPU workaround for 855873 was applied INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x80020000 INFO: SPSR = 0x3c9 INFO: BL31: DEBUG: image_type is: normal
Can anyone please suggest what could be the issue here that I don't see the test image console output ? Note, the same test image works fine using u-boot.
Regards Ravi
On Oct 7, 2020, at 12:43 PM, rkohli2000 gmail via TF-A <tf-a@lists.trustedfirmware.org mailto:tf-a@lists.trustedfirmware.org> wrote:
Hi Alexei,
Thanks for your reply. I have not verified the RESET_TO_BL1 for imx8qm yet. I will try it out and confirm. And, thanks for this suggestion.
Regards Ravi
On Oct 7, 2020, at 12:12 PM, Alexei Fedorov <Alexei.Fedorov@arm.com mailto:Alexei.Fedorov@arm.com> wrote:
Hi Ravi,
Have you tried to use RESET_TO_BL31 build option for your platform?
Regards. Alexei ________________________________ From: TF-A <tf-a-bounces@lists.trustedfirmware.org mailto:tf-a-bounces@lists.trustedfirmware.org> on behalf of rkohli2000 gmail via TF-A <tf-a@lists.trustedfirmware.org mailto:tf-a@lists.trustedfirmware.org> Sent: 07 October 2020 17:01 To: tf-a@lists.trustedfirmware.org mailto:tf-a@lists.trustedfirmware.org <tf-a@lists.trustedfirmware.org mailto:tf-a@lists.trustedfirmware.org> Subject: [TF-A] BL31 as bootloader
Hi, I'm a new user and sorry for some basic TF-A questions. Any guidance is appreciated.
I'm am able boot the TF-A bl31.bin image itself on my i.MX8QM MEK platform without using u-boot. I can use the imx-mkimage tool to create a flash or eMMC bootable image (flash.bin). Here, I can specify this container image with both bl31.bin and a separate custom app at a give flash address. This is without any security requirements or dependencies.
Can I use the T-FA bl31.bin image to act as a first stage bootloader (without u-boot) and then launch a "custom" bare metal app for Cortex-A53 (for example) on the i.MX8QM at the given (BL33) entry point 0x80020000 address ?
Thanks in advance. Ravi
-- TF-A mailing list TF-A@lists.trustedfirmware.org mailto:TF-A@lists.trustedfirmware.org https://lists.trustedfirmware.org/mailman/listinfo/tf-a https://lists.trustedfirmware.org/mailman/listinfo/tf-a
-- TF-A mailing list TF-A@lists.trustedfirmware.org mailto:TF-A@lists.trustedfirmware.org https://lists.trustedfirmware.org/mailman/listinfo/tf-a https://lists.trustedfirmware.org/mailman/listinfo/tf-a
-- TF-A mailing list TF-A@lists.trustedfirmware.org mailto:TF-A@lists.trustedfirmware.org https://lists.trustedfirmware.org/mailman/listinfo/tf-a https://lists.trustedfirmware.org/mailman/listinfo/tf-a