- TF-A - lists.trustedfirmware.org

by Chen Feng

hi expects， from the atf2.2 release notes,I can see the tf-a already supported pac bti and mte feature. I want to enable and test it on fvp platform. I want to know which tool chain to use for compiling code for theses. Cheers Feng

6 years, 3 months

1
0
0 0

Trusted Firmware version 2.2 is now available

by Bipin Ravi

Hi all, Trusted Firmware version 2.2 is now available and can be found here: https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/tag/?h=v2.2 Please refer to the readme and change log for further information. Thanks & best regards, [cid:image001.jpg@01D588EA.577B7090] Bipin Ravi | Principal Design Engineer Bipin.Ravi(a)arm.com<mailto:Joshua.Sunil@arm.com> | Skype: Bipin.Ravi.ARM Direct: +1-512-225 -1071 | Mobile: +1-214-212-0794 5707 Southwest Parkway, Suite 100, Austin, TX 78735

6 years, 3 months

1
0
0 0

[RFC] BL2 MTD frameworks

by Lionel DEBIEVE

Hello Maintainers, I've sent a patch series around MTD framework management into BL2 stage (cf https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/2283). This patch series will add following frameworks: - a raw NAND framework implementation to support SLC NAND devices. Current implementation is limited to read operations without ECC corrections. Overrides are available to use hardware ECC from controller or low-level drivers. It also supports ONFI detection management but this can also be disabled or overridden by platform specific data. - a SPI-MEM framework (inspired from kernel/u-boot implementation) that encapsulates all SPI operations to SPI low level drivers. - a SPI-NAND framework based on SPI-MEM to support SPI NAND devices. This framework is also limited to the read operation. It uses single command, address and data bus width as legacy but can be overridden by platform. - a SPI-NOR framework based on SPI-MEM to manage SPI NOR devices. It is also limited to read operations using single command, address and data bus width as legacy (override still possible by platform). The framework embeds some specific implementations for manufacturers specific behavior in case of quad mode configuration activation. This patch series also includes: - a new io_mtd interface to manage a generic access to all these frameworks. - a NAND core driver that accesses independently to raw NAND or SPI-NAND framework. This core driver requires a scratch buffer defined by platform to manage unaligned pages (could be defined to 0 in case of aligned page) and limits access to a single NAND instance management. - a complete integration is available based on STM32MP1 platform. Tests have been performed with the following devices: SLC NAND: - Micron MT29F8G08ABACAH4 (ONFI) - Micron MT29F8G16ABACAH4 (ONFI) - Toshiba TH58NVG3S0HTAI0 (Non ONFI) - Toshiba TC58BVG1S3HTAI0 (On die ECC) SPI NOR: - Macronix MX25L51245G - Cypress/Spansion S25FL512 - Micron n25q512ax3 SPI-NAND: - Micron MT29F2G01ABAGD Waiting for your comments. Best regards, Lionel

6 years, 3 months

1
0
0 0

Re: [TF-A] Boot getting stuck on RK3399 Rockpro64 board

by Joanna Farley

Hi Hugh, Ccing the Rockchip maintainers from https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/tree/docs/maint… as neither appear to be subscribed to this mailing list. Joanna On 08/10/2019, 21:45, "TF-A on behalf of Hugh Cole-Baker via TF-A" <tf-a-bounces(a)lists.trustedfirmware.org on behalf of tf-a(a)lists.trustedfirmware.org> wrote: Hi folks, I've been using TF-A with mainline U-Boot recently as firmware & boot loader for a RK3399 Rockpro64 board. I'm compiling TF-A and U-boot based on this guide [1], using gcc 8.3.0 from Debian. TF-A v2.1 works fine for this, but I recently tried to switch to TF-A latest master and found U-Boot gets stuck with this version. The symptoms are: U-Boot TPL and SPL print starting messages like this: U-Boot TPL 2019.10-rc4-00037-gdac51e9aaf (Oct 06 2019 - 21:42:50) Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2019.10-rc4-00037-gdac51e9aaf (Oct 06 2019 - 21:42:50 +0000) Trying to boot from MMC2 ...and then there is no more output when normally U-Boot proper would start, and go on to load the Linux kernel, etc. Starting from v2.1, with git bisect I found the first 'bad' commit is: 0aad563c7480 rockchip: Update BL31_BASE to 0x40000 and that commit does change some RK3399-related files so seems likely. I'm not sure how to debug further, any ideas on why boot is hanging after that change or how to get more debugging information? Best regards, Hugh Cole-Baker [1] https://github.com/u-boot/u-boot/blob/master/doc/README.rockchip -- TF-A mailing list TF-A(a)lists.trustedfirmware.org https://lists.trustedfirmware.org/mailman/listinfo/tf-a IMPORTANT NOTICE: The contents of this email and any attachments are confidential and may also be privileged. If you are not the intended recipient, please notify the sender immediately and do not disclose the contents to any other person, use it for any purpose, or store or copy the information in any medium. Thank you.

6 years, 4 months

2
1
0 0

Re: [TF-A] Hercules-AE I$ problems

by Olivier Deprez

Hi Varun, TF-A v1.4 is rather old codebase, can you provide the exact patchset you cherry-picked on top of it? e.g. you need the Hercules CPU support patch (a4668c36f1fca75b), but possibly also all which is related to HW_ASSISTED_COHERENCY option? Also, can you pls provide your build cmd line? Thanks & Regards, Olivier. ________________________________ From: TF-A <tf-a-bounces(a)lists.trustedfirmware.org> on behalf of Soby Mathew via TF-A <tf-a(a)lists.trustedfirmware.org> Sent: 11 October 2019 11:21 To: Varun Wadekar <vwadekar(a)nvidia.com>; Joanna Farley <Joanna.Farley(a)arm.com>; Matteo Carlini <Matteo.Carlini(a)arm.com> Cc: Julius Werner via TF-A <tf-a(a)lists.trustedfirmware.org>; nd <nd(a)arm.com> Subject: Re: [TF-A] Hercules-AE I$ problems On 10/10/2019 20:46, Varun Wadekar wrote: > Hello, > > First of all, thanks a lot for posting the Hercules-AE patches. > > We picked them up and used them internally. Unfortunately, the CPU sees > garbage in it's I$ when we enable the I cache for the processor. If we > keep I$ disabled, TF-A boots properly. We are using TF-A v1.4 for > verification. > > We booted Linux kernel v4.14 on the processor and don't see this problem > there. So, we suspect something going wrong inside TF-A. Have you seen > this problem internally? Any hints or clues to solve it would be helpful. > > Thanks. Hi Varun, As indicated in the commit message of the patch, we have not tested the CPU support internally due to non-availability of FVP for the CPU. TF-A assumes that I$ will be invalidated when CPU is reset. Perhaps this is not true for your setup. Could you try adding a `IC IALLU` in the CPU reset handler prior to I$ enable and see if that improves anything ? Best Regards Soby Mathew > > > ------------------------------------------------------------------------ > This email message is for the sole use of the intended recipient(s) and > may contain confidential information. Any unauthorized review, use, > disclosure or distribution is prohibited. If you are not the intended > recipient, please contact the sender by reply email and destroy all > copies of the original message. > ------------------------------------------------------------------------ -- TF-A mailing list TF-A(a)lists.trustedfirmware.org https://lists.trustedfirmware.org/mailman/listinfo/tf-a IMPORTANT NOTICE: The contents of this email and any attachments are confidential and may also be privileged. If you are not the intended recipient, please notify the sender immediately and do not disclose the contents to any other person, use it for any purpose, or store or copy the information in any medium. Thank you.

6 years, 4 months

1
0
0 0

Hercules-AE I$ problems

by Varun Wadekar

Hello, First of all, thanks a lot for posting the Hercules-AE patches. We picked them up and used them internally. Unfortunately, the CPU sees garbage in it's I$ when we enable the I cache for the processor. If we keep I$ disabled, TF-A boots properly. We are using TF-A v1.4 for verification. We booted Linux kernel v4.14 on the processor and don't see this problem there. So, we suspect something going wrong inside TF-A. Have you seen this problem internally? Any hints or clues to solve it would be helpful. Thanks. ----------------------------------------------------------------------------------- This email message is for the sole use of the intended recipient(s) and may contain confidential information. Any unauthorized review, use, disclosure or distribution is prohibited. If you are not the intended recipient, please contact the sender by reply email and destroy all copies of the original message. -----------------------------------------------------------------------------------

6 years, 4 months

2
1
0 0

Documentation and Website Updates

by Paul Beesley

Hi everyone, This post is to let you know about some changes to the TrustedFirmware.org website and to the TF-A documentation. It briefly covers what's new, what has moved, and what happens to any existing resources you may be using. First of all, we are making it more obvious where to access the documentation and the Gerrit review system. The front page of trustedfirmware.org has grown new "Documentation" and "Review" menus with links to this content. Dashboard and Wiki items have moved under the Documentation menu. Secondly, the online version of the documentation has moved to www.trustedfirmware.org/docs/tf-a<http://www.trustedfirmware.org/docs/tf-a>. This is a pre-rendered, HTML copy of the content that is found under the "docs" directory of the TF-A repository. The content here will remain synchronised with the master branch of the repository. Following the v2.2 release, you will also be able to access a static version of the documentation that corresponds to that tag, via a version selection drop-down menu on the site. The intention behind this change is to make it easier to find the docs, to improve the output quality and to make the content more modular and readable. The new setup has a persistent table of contents (displayed to the left of the page content) and a search feature, making it easier to find what you're looking for and easier to move between documents and topics. You may be used to viewing the docs through either the git viewer (https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/about/) or through the Github mirror (https://github.com/ARM-software/arm-trusted-firmware/). The landing pages of these sites now contain links to the new content. While you can still use these sites to access other documentation content, you may find that there are some formatting warnings displayed if you do so. Finally, if you prefer to read a local copy of the documentation on your machine then you can build the same HTML output following the instructions at https://trustedfirmware-a.readthedocs.io/en/latest/getting_started/docs-bui… (or docs/getting_started/docs-build.rst, for the equivalent file in the repository). As always, let us know if you have any comments or if there are other changes you would like to see. Thanks, Paul

6 years, 4 months

1
0
0 0

Boot getting stuck on RK3399 Rockpro64 board

by Hugh Cole-Baker

Hi folks, I've been using TF-A with mainline U-Boot recently as firmware & boot loader for a RK3399 Rockpro64 board. I'm compiling TF-A and U-boot based on this guide [1], using gcc 8.3.0 from Debian. TF-A v2.1 works fine for this, but I recently tried to switch to TF-A latest master and found U-Boot gets stuck with this version. The symptoms are: U-Boot TPL and SPL print starting messages like this: U-Boot TPL 2019.10-rc4-00037-gdac51e9aaf (Oct 06 2019 - 21:42:50) Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2019.10-rc4-00037-gdac51e9aaf (Oct 06 2019 - 21:42:50 +0000) Trying to boot from MMC2 ...and then there is no more output when normally U-Boot proper would start, and go on to load the Linux kernel, etc. Starting from v2.1, with git bisect I found the first 'bad' commit is: 0aad563c7480 rockchip: Update BL31_BASE to 0x40000 and that commit does change some RK3399-related files so seems likely. I'm not sure how to debug further, any ideas on why boot is hanging after that change or how to get more debugging information? Best regards, Hugh Cole-Baker [1] https://github.com/u-boot/u-boot/blob/master/doc/README.rockchip

6 years, 4 months

1
0
0 0

Forthcoming Trusted Firmware-A 2.2 release

by Bipin Ravi

Hi, This is to notify that we are planning to target the Trusted Firmware-A 2.2 release during the third week of October as part of the regular 6 month cadence. The aim is to consolidate all TF-A work since the 2.1 release. As part of this, a release candidate tag will be created and release activities will commence from Monday October 7th. Essentially we will not merge any major enhancements from this date until the release is made. Please ensure any Pull Requests (PR's) desired to make the 2.2 release are submitted in good time to be complete by Friday October 4th. Any major enhancement PR's still open after that date will not be merged until after the release. Thanks & best regards, [cid:image001.jpg@01D57244.98C07530] Bipin Ravi | Principal Design Engineer Bipin.Ravi(a)arm.com<mailto:Joshua.Sunil@arm.com> | Skype: Bipin.Ravi.ARM Direct: +1-512-225 -1071 | Mobile: +1-214-212-0794 5707 Southwest Parkway, Suite 100, Austin, TX 78735

6 years, 4 months

1
0
0 0

New Defects reported by Coverity Scan for ARM-software/arm-trusted-firmware

by scan-admin＠coverity.com

Hi, Please find the latest report on new defect(s) introduced to ARM-software/arm-trusted-firmware found with Coverity Scan. 1 new defect(s) introduced to ARM-software/arm-trusted-firmware found with Coverity Scan. New defect(s) Reported-by: Coverity Scan Showing 1 of 1 defect(s) ** CID 349459: (ARRAY_VS_SINGLETON) ________________________________________________________________________________________________________ *** CID 349459: (ARRAY_VS_SINGLETON) /plat/mediatek/mt8183/drivers/sspm/sspm.c: 150 in sspm_alive_show() 144 145 if (sspm_ipi_send_non_blocking(IPI_ID_PLATFORM, &ipi_data) != 0) { 146 ERROR("sspm init send fail! ret=%d\n", ret); 147 return -1; 148 } 149 >>> CID 349459: (ARRAY_VS_SINGLETON) >>> Passing "&ipi_data" to function "sspm_ipi_recv_non_blocking" which uses it as an array. This might corrupt or misinterpret adjacent memory locations. 150 while (sspm_ipi_recv_non_blocking(IPI_ID_PLATFORM, 151 &ipi_data, 152 sizeof(ipi_data)) 153 && count) { 154 mdelay(100); 155 count--; 156 } 157 158 return (ipi_data == 1) ? 0 : -1; /plat/mediatek/mt8183/drivers/sspm/sspm.c: 145 in sspm_alive_show() 139 uint32_t ipi_data, count; 140 int ret = 0; 141 142 count = 5; 143 ipi_data = 0xdead; 144 >>> CID 349459: (ARRAY_VS_SINGLETON) >>> Passing "&ipi_data" to function "sspm_ipi_send_non_blocking" which uses it as an array. This might corrupt or misinterpret adjacent memory locations. 145 if (sspm_ipi_send_non_blocking(IPI_ID_PLATFORM, &ipi_data) != 0) { 146 ERROR("sspm init send fail! ret=%d\n", ret); 147 return -1; 148 } 149 150 while (sspm_ipi_recv_non_blocking(IPI_ID_PLATFORM, ________________________________________________________________________________________________________ To view the defects in Coverity Scan visit, https://u2389337.ct.sendgrid.net/wf/click?upn=08onrYu34A-2BWcWUl-2F-2BfV0V0…

6 years, 4 months

1
0
0 0

2026

2025

2024

2023

2022

2021

2020

2019

2018

TF-A