Hi Kevin,
I don't know much about JLink so cannot help with setup, but there is a quick workaround if reset does not work: insert a "B ." instruction on the first line of the reset handler in the startup file. Then the target will sit in an infinite loop while you connect with the debugger, and afterwards you can use the debugger to increment the PC by two to step over the instruction.
The typical debug setup in the TF-M team is to use either a Keil ULINKpro or Arm DSTREAM debugger with Arm Development Studio or Keil uVision. Most issues can be debugged on the FVP too, which runs a debug server when the "-S" option is passed.
Kind regards, Jamie
-----Original Message----- From: TF-M tf-m-bounces@lists.trustedfirmware.org On Behalf Of Kevin Townsend via TF-M Sent: 19 August 2019 13:45 To: Kevin Townsend kevin.townsend@linaro.org Cc: Thomas Törnblom via TF-M tf-m@lists.trustedfirmware.org Subject: Re: [TF-M] Debugger setup for MPS2+ AN521
Hi,
Any feedback at all on debugging TF-M on AN521 with a HW debugger, or confirmation someone has a working setup?
I'm curious how people are digging into particularly complex problems, or things that happen very early on (pre-printf) if a standard HW debugger over SWD/JTAG isn't an option?
Many thanks, Kevin
On Tue, 6 Aug 2019 at 13:50, Kevin Townsend via TF-M tf-m@lists.trustedfirmware.org wrote:
tl;dr: unable to connect to MPS2+ AN521 with JLink and perform a soft reset to halt at NSPE init, and debug an init issue. Connect via SWD fails, connect via JTAG seems OK, but soft reset requests consistently fail, preventing meaningful debug/trace of the code. Looking for advice on known-good debug setup with GDB and Linux.
Full explanation follows:
I'm currently working on an application with the following setup:
- TF-M (latest) running in the secure processing environment
- Zephyr running in the NSPE
- PSA FF APIs to communicate between PEs
I've run into a HW problem with the UART peripheral that I need to debug, but using a J-Link has been problematic, and I was curious if anyone else has had any success with GDB or JLinkExe and the MPS2+.
To debug, I currently do the following:
- Copy a valid TF-M + Zephyr and BL2 image to the MPS2+
- Physically reset the MPS2+ (AN521)
- Wait for the image to start up (based on serial output)
- Connect the debugger
- Attempt to reset
I get the following output at connect (entering the 'connect' command at the J-Link prompt):
NOTE: I've been unable to get SWD to work, and had to fall back to JTAG for the interface.
$ JLinkExe -device Cortex-M33 -if jtag -speed auto SEGGER J-Link Commander V6.44i (Compiled May 17 2019 17:38:03) DLL version V6.44i, compiled May 17 2019 17:37:52
Connecting to J-Link via USB...O.K. Firmware: J-Link V9 compiled May 17 2019 09:50:41 Hardware version: V9.10 S/N: 609100327 License(s): RDI, FlashBP, FlashDL, JFlash, GDB VTref=3.011V Device position in JTAG chain (IRPre,DRPre) <Default>: -1,-1 => Auto-detect JTAGConf>connect ERROR while parsing value for IRPre. Using default: -1. ERROR while parsing value for DRPre. Using default: -1. Device "CORTEX-M33" selected.
Connecting to target via JTAG TotalIRLen = 4, IRPrint = 0x01 JTAG chain detection found 1 devices: #0 Id: 0x6BA00477, IRLen: 04, CoreSight JTAG-DP Scanning AP map to find all available APs AP[3]: Stopped AP scan as end of AP map has been reached AP[0]: APB-AP (IDR: 0x54770002) AP[1]: AHB-AP (IDR: 0x84770001) AP[2]: AHB-AP (IDR: 0x84770001) Iterating through AP map to find AHB-AP to use AP[0]: Skipped. Not an AHB-AP AP[1]: Core found AP[1]: AHB-AP ROM base: 0xF0008000 CPUID register: 0x410FD211. Implementer code: 0x41 (ARM) Found Cortex-M33 r0p1, Little endian. FPUnit: 8 code (BP) slots and 0 literal slots Security extension: implemented Secure debug: enabled CoreSight components: ROMTbl[0] @ F0008000 ROMTbl[0][0]: F0009000, CID: B105900D, PID: 000BB9A4 GPR ROMTbl[0][1]: E00FF000, CID: B105100D, PID: 000BB4C9 ROM Table ROMTbl[1] @ E00FF000 ROMTbl[1][0]: E000E000, CID: B105900D, PID: 000BBD21 Cortex-M33 ROMTbl[1][1]: E0001000, CID: B105900D, PID: 000BBD21 DWT ROMTbl[1][2]: E0002000, CID: B105900D, PID: 000BBD21 FPB ROMTbl[1][3]: E0000000, CID: B105900D, PID: 000BBD21 ITM ROMTbl[1][5]: E0041000, CID: B105900D, PID: 001BBD21 ETM ROMTbl[1][6]: E0042000, CID: B105900D, PID: 000BBD21 CTI Cortex-M33 identified.
But any attempt to perform a soft reset fails, which makes debugging the init code problematic:
J-Link>r 0 Reset delay: 0 ms Reset type NORMAL: Resets core & peripherals via SYSRESETREQ & VECTRESET bit. Reset: Halt core after reset via DEMCR.VC_CORERESET. Reset: Reset device via AIRCR.SYSRESETREQ. Reset: CPU may have not been reset (DHCSR.S_RESET_ST never gets set). Reset: Using fallback: Reset pin. Reset: Halt core after reset via DEMCR.VC_CORERESET. Reset: Reset device via reset pin Reset: VC_CORERESET did not halt CPU. (Debug logic also reset by reset pin?). Reset: Reconnecting and manually halting CPU. AP map detection skipped. Manually configured AP map found. AP[0]: CUSTOM-AP (IDR: Not set) AP[1]: AHB-AP (IDR: Not set) AP[1]: Skipped. Invalid implementer code read from CPUIDVal[31:24] = 0x00 AP map detection skipped. Manually configured AP map found. AP[0]: CUSTOM-AP (IDR: Not set) AP[1]: AHB-AP (IDR: Not set) AP[1]: Skipped. Invalid implementer code read from CPUIDVal[31:24] = 0x00
WARNING: CPU could not be halted
Reset: Core did not halt after reset, trying to disable WDT. Reset: Halt core after reset via DEMCR.VC_CORERESET. Reset: Reset device via reset pin Reset: VC_CORERESET did not halt CPU. (Debug logic also reset by reset pin?). Reset: Reconnecting and manually halting CPU. AP map detection skipped. Manually configured AP map found. AP[0]: CUSTOM-AP (IDR: Not set) AP[1]: AHB-AP (IDR: Not set) AP[1]: Skipped. Invalid implementer code read from CPUIDVal[31:24] = 0x00 AP map detection skipped. Manually configured AP map found. AP[0]: CUSTOM-AP (IDR: Not set) AP[1]: AHB-AP (IDR: Not set) AP[1]: Skipped. Invalid implementer code read from CPUIDVal[31:24] = 0x00
WARNING: CPU could not be halted
****** Error: Could not find core in Coresight setup
If anyone is using a J-Link or J-Trace and ideally GDB to do any meaningful debugging or tracing on the MPS2+ any suggestions on proper setup would be valuable, and I'm happy to document an eventual working config for inclusion in the project doc files.
Barring that, an alternative GDB-based setup would be useful if someone has a known-good solution?
Best regards, Kevin Townsend -- TF-M mailing list TF-M@lists.trustedfirmware.org https://lists.trustedfirmware.org/mailman/listinfo/tf-m
-- TF-M mailing list TF-M@lists.trustedfirmware.org https://lists.trustedfirmware.org/mailman/listinfo/tf-m