Hi,
The patch is there: https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/13023
Best regards, Yann
On 12/13/21 5:34 PM, Manish Badarkhe wrote:
Hi Yann,
Adding helper in the FCONF library will be good idea. Please post the patch to review it.
Thanks, Manish Badarkhe
*From: *Yann Gautier yann.gautier@foss.st.com *Date: *Monday, 13 December 2021 at 14:37 *To: *Manish Badarkhe Manish.Badarkhe@arm.com, tf-a@lists.trustedfirmware.org tf-a@lists.trustedfirmware.org *Subject: *Re: [TF-A] FCONF warning for TOS_FW_CONFIG
Hi Manish,
I've checked what could be done for this warning. The easiest way would be to create a new helper in lib/fconf/fconf_dyn_cfg_getter.c. My idea is to create a function: unsigned int dyn_cfg_dtb_info_get_index(unsigned int config_id). It returns the index of the config_id image in the dtb_infos[]. Or FCONF_INVALID_IDX (0xFFFFFFFFU) if it is not found.
I can then check if the TOS_FW_CONFIG is inside the FIP if dyn_cfg_dtb_info_get_index(TOS_FW_CONFIG_ID) != FCONF_INVALID_IDX
I could have used a boolean function, but doing so allows factoring code in dyn_cfg_dtb_info_getter().
Do you think it could be OK?
Thanks, Yann
On 12/10/21 9:29 AM, Yann Gautier via TF-A wrote:
Hi Manish,
Thanks for your answers. I fear that's a kind of chicken and egg story. To know what BL32 is used, I need to check what's in the FIP. I will check with the fconf populator function (fconf_populate_stm32mp_io_policies()) if there is a way to retrieve and keep the information.
Best regards, Yann
On 12/7/21 8:56 PM, Manish Badarkhe wrote:
Hi Yann,
I realized now, the patch I proposed does not work for you to run the same BL2 image with OP-TEE (BL32) or SP_min (BL32) run.
IMO then better retrieve the TOS_FW_CONFIG info run-time.
Is there any way to differentiate OP-TEE or SP_min run in the ST platform to use it as a run-time check?
Thanks,
Manish Badarkhe
*From: *TF-A tf-a-bounces@lists.trustedfirmware.org on behalf of Manish Badarkhe via TF-A tf-a@lists.trustedfirmware.org *Date: *Tuesday, 7 December 2021 at 18:32 *To: *Yann Gautier yann.gautier@foss.st.com, tf-a@lists.trustedfirmware.org tf-a@lists.trustedfirmware.org *Subject: *Re: [TF-A] FCONF warning for TOS_FW_CONFIG
Hi Yann,
IMO, platform should not pass ‘TOS_FW_CONFIG_ID’ to this generic function ‘‘dyn_cfg_dtb_info_getter’ while using OPTEE.
It is better not to handle specific scenarios mentioned in your proposed patch in the generic library function, but let me know what do you think?
I would suggest below modifications in the platform code instead:
diff --git a/plat/st/stm32mp1/bl2_plat_setup.c b/plat/st/stm32mp1/bl2_plat_setup.c
index 7eaf0ed98..96e24401e 100644
--- a/plat/st/stm32mp1/bl2_plat_setup.c
+++ b/plat/st/stm32mp1/bl2_plat_setup.c
@@ -357,7 +357,9 @@ int bl2_plat_handle_post_image_load(unsigned int image_id)
BL32_IMAGE_ID,
BL33_IMAGE_ID,
HW_CONFIG_ID,
+#ifndef AARCH32_SP_OPTEE
TOS_FW_CONFIG_ID,
+#endif
};
#endif /* !STM32MP_USE_STM32IMAGE */
Thanks,
Manish Badarkhe
*From: *TF-A tf-a-bounces@lists.trustedfirmware.org on behalf of Yann Gautier via TF-A tf-a@lists.trustedfirmware.org *Date: *Friday, 3 December 2021 at 10:44 *To: *tf-a@lists.trustedfirmware.org tf-a@lists.trustedfirmware.org *Subject: *[TF-A] FCONF warning for TOS_FW_CONFIG
Hi,
On STM32MP1, we'd like BL2 to be agnostic of what BL32 is in the FIP. It can be either OP-TEE or TF-A SP_min.
But on STM32MP1, SP_min needs a device tree file (TOS_FW_CONFIG_ID), whereas OP-TEE doesn't use this separate DT image.
As TOS_FW_CONFIG_ID is in list of images to be loaded by BL2, we then have a warning message in case OP-TEE is used: WARNING: FCONF: Invalid config id 26
I'd like to silence this warning with this kind of patch: diff --git a/lib/fconf/fconf_dyn_cfg_getter.c b/lib/fconf/fconf_dyn_cfg_getter.c index 25dd7f9eda..f7e9834c3b 100644 --- a/lib/fconf/fconf_dyn_cfg_getter.c +++ b/lib/fconf/fconf_dyn_cfg_getter.c @@ -51,7 +51,11 @@ struct dyn_cfg_dtb_info_t *dyn_cfg_dtb_info_getter(unsigned int config_id) } }
- WARN("FCONF: Invalid config id %u\n", config_id); + if (config_id == TOS_FW_CONFIG_ID) { + VERBOSE("FCONF: No TOS_FW_CONFIG image\n"); + } else { + WARN("FCONF: Invalid config id %u\n", config_id); + }
return NULL; }
I can change the VERBOSE message to INFO.
Do you think it is OK if I push the patch?
Thanks, Yann -- TF-A mailing list TF-A@lists.trustedfirmware.org https://lists.trustedfirmware.org/mailman/listinfo/tf-a
https://lists.trustedfirmware.org/mailman/listinfo/tf-a
https://lists.trustedfirmware.org/mailman/listinfo/tf-a>