Hi Raymond,

 

The build command and the hex creation are correct.

 

Could you try to erase the entire eFlash before programming it?

 

It can be done with Keil MDK, or you can create a hex file with srec_cat which only contains 0xFF bytes and program that one to the board.

 

Let me know whether does it solved the issue.

 

Tamas

From: Raymond Ngun <Raymond.Ngun@cypress.com>
Sent: 05 October 2020 23:07
To: Tamas Ban <Tamas.Ban@arm.com>; tf-m@lists.trustedfirmware.org
Cc: nd <nd@arm.com>
Subject: RE: Musca-B1 and new build system

 

Thanks Tamas.

 

Unfortunately, this did not work for me.  Here is what I did to build.  Let me know if I did something wrong.

 

cmake -DTFM_PLATFORM=musca_b1 -DCMAKE_TOOLCHAIN_FILE=../toolchain_GNUARM.cmake -DCMAKE_BUILD_TYPE=Debug -DTEST_NS=ON -DTEST_S=ON ../

cmake --build . --target install

srec_cat install/outputs/MUSCA_B1/bl2.bin -Binary -offset 0xA000000 install/outputs/MUSCA_B1/tfm_s_ns_signed.bin -Binary -offset 0xA020000 -o tfm.hex -Intel

 

The resultant output is the following.

 

Entering standby..

[INF] Starting bootloader

[ERR] Error while initializing the security counter

 

Thank you,

 

Ray

 

From: Tamas Ban <Tamas.Ban@arm.com>
Sent: Thursday, October 1, 2020 3:05 AM
To: tf-m@lists.trustedfirmware.org; Raymond Ngun <Raymond.Ngun@cypress.com>
Cc: nd <nd@arm.com>
Subject: RE: Musca-B1 and new build system

 

Hi Raymond,

 

Here is the proposed fix:
https://review.trustedfirmware.org/c/TF-M/trusted-firmware-m/+/6028

 

Could you verify on your board? Pls use at build -DCMAKE_BUILD_TYPE=Debug for full logging in bootloader.

 

Tamas

 

From: TF-M <tf-m-bounces@lists.trustedfirmware.org> On Behalf Of Tamas Ban via TF-M
Sent: 01 October 2020 10:37
To: Raymond Ngun <Raymond.Ngun@cypress.com>; tf-m@lists.trustedfirmware.org
Cc: nd <nd@arm.com>
Subject: Re: [TF-M] Musca-B1 and new build system

 

Hi Raymond,

 

Thanks for reporting the issue! 

 

The observed behaviour has two reason:
- In the new build system the default CMAKE_BUILD_TYPE=Release. In this case the logging is disabled in MCUboot to get smaller binary.  You can set manualy to Debug in the command line to enable logging from bootloader

 

Tamas

 

From: TF-M <tf-m-bounces@lists.trustedfirmware.org> On Behalf Of Raymond Ngun via TF-M
Sent: 30 September 2020 17:44
To: David Hu via TF-M <tf-m@lists.trustedfirmware.org>
Subject: [TF-M] Musca-B1 and new build system

 

Hi all,

 

I am attempting to build Musca-B1 with the latest in master but I’m not able to get it to run (nothing shows on the UART). At a minimum, the User Guide is out of date in terms of how the final hex is created. So, I have a couple questions.

 

  1. Is the latest tested with Musca-B1?
  2. Can I obtain some updated information on how to build and create an image for Musca-B1?

 

Thank you,


Ray


This message and any attachments may contain confidential information from Cypress or its subsidiaries. If it has been received in error, please advise the sender and immediately delete this message.


This message and any attachments may contain confidential information from Cypress or its subsidiaries. If it has been received in error, please advise the sender and immediately delete this message.